TX Knives

Functional handmade kitchen knives

  • Sold
  • 240mm Stainless Gyuto

240mm Stainless Gyuto

400.00
sold out
DSCF4293.jpg
DSCF4292.jpg
DSCF4295.jpg
DSCF4294.jpg
DSCF4300.jpg
DSCF4301.jpg
DSCF4302.jpg
DSCF4299.jpg
DSCF4304.jpg

240mm Stainless Gyuto

400.00
sold out

#67

Lightweight and fairly large Gyuto in high tech stainless powder metallurgy steel. It has been ground very thin, the thickness behind the edge is <0.1mm

The steel is Elmax from the Swedish company Uddeholm

Weight: 228g

Length overall: 365mm

Balance point: Under the X of the logo.

Blade

The blade has a mostly flat grind, but transitions in to convex at the higher part of the blade. It is tapered from the bolster to the tip.

The spine and choil has been rounded to make the knife comfortable to use with a pinch grip.

This blade is very thin behind the edge, <0.1mm just over the secondary bevel. The thickness is around 0.4mm 10mm from the tip.

 

Steel: Elmax

Elmax is a powder metallurgy stainless steel created by Bohler-Uddenholm. It is corrosive resistant due to its high Chromium percentage. It also has excellent edge holding capabilities. It is a fairly easy steel to sharpen and it becomes razor sharp due to the powder metallurgy process and the limited impurities.


 

Heat treatment: The blade has been differentially heat treated inhouse in a PID controlled furnace at 1100°C and quenched between thick aluminium plates. Finally it is tempered in a PID controlled oven to the final hardness.

 

Hardness: 63 HRC

Height at heel: 58mm

Thickness at

  • Spine at bolster: 2.3mm

  • Spine halfway: 2.0mm

  • 1 cm from the tip: 0.4mm

Handle

Material: Stabilized bog oak

Bolster and spacers: Stainless 303 bolster pinned to the blade with 303 pins, G10 and stainless spacers. Stainless 6mm 304 handle pin.
Treatment: The handle is treated with Danish Oil

Add To Cart

#67

Lightweight and fairly large Gyuto in high tech stainless powder metallurgy steel. It has been ground very thin, the thickness behind the edge is <0.1mm

The steel is Elmax from the Swedish company Uddeholm

Weight: 228g

Length overall: 365mm

Balance point: Under the X of the logo.

Blade

The blade has a mostly flat grind, but transitions in to convex at the higher part of the blade. It is tapered from the bolster to the tip.

The spine and choil has been rounded to make the knife comfortable to use with a pinch grip.

This blade is very thin behind the edge, <0.1mm just over the secondary bevel. The thickness is around 0.4mm 10mm from the tip.

 

Steel: Elmax

Elmax is a powder metallurgy stainless steel created by Bohler-Uddenholm. It is corrosive resistant due to its high Chromium percentage. It also has excellent edge holding capabilities. It is a fairly easy steel to sharpen and it becomes razor sharp due to the powder metallurgy process and the limited impurities.


 

Heat treatment: The blade has been differentially heat treated inhouse in a PID controlled furnace at 1100°C and quenched between thick aluminium plates. Finally it is tempered in a PID controlled oven to the final hardness.

 

Hardness: 63 HRC

Height at heel: 58mm

Thickness at

  • Spine at bolster: 2.3mm

  • Spine halfway: 2.0mm

  • 1 cm from the tip: 0.4mm

Handle

Material: Stabilized bog oak

Bolster and spacers: Stainless 303 bolster pinned to the blade with 303 pins, G10 and stainless spacers. Stainless 6mm 304 handle pin.
Treatment: The handle is treated with Danish Oil