TX Knives

Functional handmade kitchen knives

  • Sold
  • 270mm Stainless Gyuto Custom order

270mm Stainless Gyuto Custom order

0.00
sold out
DSCF4312.jpg
DSCF4313.jpg
DSCF4318.jpg
DSCF4316.jpg
DSCF4325.jpg
DSCF4322.jpg
DSCF4326.jpg
DSCF4329.jpg
DSCF4334.jpg

270mm Stainless Gyuto Custom order

0.00
sold out

#66

Large but light Gyuto in high tech stainless powder metallurgy steel. It has been ground very thin, the thickness behind the edge is ~0.15mm near the heel and ~0.1mm at the tip.

The steel is Elmax from the Swedish company Uddeholm

Weight: 200g

Length overall: 400mm

Balance point: 35mm from the bolster

Blade

The blade has a mostly flat grind, but transitions in to convex at the higher part of the blade. It is tapered from the bolster to the tip.

The spine and choil has been rounded to make the knife comfortable to use with a pinch grip.

This blade is very thin behind the edge and qualifies as a laser.

Steel: Elmax

Elmax is a powder metallurgy stainless steel created by Bohler-Uddenholm. It is corrosive resistant due to its high Chromium percentage. It also has excellent edge holding capabilities. It is a fairly easy steel to sharpen and it becomes razor sharp due to the powder metallurgy process and the limited impurities.

 

Heat treatment: The blade has been differentially heat treated inhouse in a PID controlled furnace at 1100°C and quenched between thick aluminium plates. Finally it is tempered in a PID controlled oven to the final hardness.

 

Hardness: 61 HRC

Height at heel: 58mm

Thickness at

  • Spine at bolster: 2.4mm

  • Spine halfway: 1.9mm

  • 1 cm from the tip: 0.35mm

Handle

Material: Stabilized chestnut

Bolster and spacers: Black acetal bolster and G10 stainless spacers. 5mm carbon fiber handle pin.
Treatment: The handle has been sealed with Danish Oil

Add To Cart

#66

Large but light Gyuto in high tech stainless powder metallurgy steel. It has been ground very thin, the thickness behind the edge is ~0.15mm near the heel and ~0.1mm at the tip.

The steel is Elmax from the Swedish company Uddeholm

Weight: 200g

Length overall: 400mm

Balance point: 35mm from the bolster

Blade

The blade has a mostly flat grind, but transitions in to convex at the higher part of the blade. It is tapered from the bolster to the tip.

The spine and choil has been rounded to make the knife comfortable to use with a pinch grip.

This blade is very thin behind the edge and qualifies as a laser.

Steel: Elmax

Elmax is a powder metallurgy stainless steel created by Bohler-Uddenholm. It is corrosive resistant due to its high Chromium percentage. It also has excellent edge holding capabilities. It is a fairly easy steel to sharpen and it becomes razor sharp due to the powder metallurgy process and the limited impurities.

 

Heat treatment: The blade has been differentially heat treated inhouse in a PID controlled furnace at 1100°C and quenched between thick aluminium plates. Finally it is tempered in a PID controlled oven to the final hardness.

 

Hardness: 61 HRC

Height at heel: 58mm

Thickness at

  • Spine at bolster: 2.4mm

  • Spine halfway: 1.9mm

  • 1 cm from the tip: 0.35mm

Handle

Material: Stabilized chestnut

Bolster and spacers: Black acetal bolster and G10 stainless spacers. 5mm carbon fiber handle pin.
Treatment: The handle has been sealed with Danish Oil